The MAXIMUS 11 Version 13 Series is our latest cell design both inside and out. Push in quick release 90 degree brass swivel fittings makes this unit a breeze to fit and you can add more cells quickly without fuss. Quick release metal fittings all the way from cell to engine. With bigger outlets the MAXIMUS 11 produces more gas with much less effort.
Enough HHO for up to a 3.0 litre diesel or petrol engine and is able to have more cells added where needed. This unit has a bigger bubbler and 3/8 flow ports. Bigger ports prevent choking of the cell and allows free flow of electrolyte thus more gas! We at NQ Hybrids with the help of a few dilligent customers have been experimenting with Sodium Carb for quite a while it is more stable than KOH and does not change the amps with fluid concentration levels and the amps are less eratic so no PWM is needed. From a safety point SD is safe to handle and less aggressive on paint and alloys.
All metal push in fittings. 12 Self Tapping Mount Screws. Purpose built HHO 1.0 litre Bubbler tank. All electrical tabs and fittings needed. SODIUM CARBONATE (Lab Grade) for 4 litres plus.Please note: We do not include the wire. Suggested size 6mm auto wire for small 11 and 21 plate and 12mm for Brutus and twin cell systems. Wire size is relevant to distance from source and amp draw. IF the question is not answered below please when requsting information give size of engine in cc. Age, make and if diesel or petrol.
What are your cells made of? We use only 316L 18 gauge Stainless Steel in all our HHO Generators. The Plates Used in Our Dry Cells Are All Laser Cut, this does have an effect on performance and production of hho gas! The Acrylic end caps are 100mmX100mm X12mm thick rated at 145 degrees C.The 2 hose barbs are 3/8 The attachment bracket angles are aluminium 2 X 6mm wing nuts for easy connection to the power source. What size cell do I need.
An 11 plate cell will do a 2500 cc engine with ease. For larger V6 V8 a 21 plate cell or two 11 plate cells together. Can I run my car totally on HHO? HHO is added to your engine and acts as a catalyst to ensure that a greater amount of fuel is burnt rather than thrown out the exhaust or wasted in generating heat and vibration.This in turn increases performance by smoothing out and improving overall operation. Almost immediately you will notice a significant reduction in engine noise, as a more complete combustion helps the engine to cycle correctly, this results in noticeable power increase.
Over the next month or so the engine will remove built up carbon deposits from unburnt fuel, further increasing your performance & mileage and reducing your emissions. Fuel savings will depend greatly on the current inefficiency of your cars engine. Some older vehicles can get around 30 to 40% savings. Does it make a difference if it is a Petrol or Diesel Engine?
HHO will work on both Diesel and Petrol engines. Is a HHO dry cell system hard. All our dry cells and kits have complete detailed installation instructions delivered with them.
On average with the right tools and some mechanical know how it should not take longer than a few of hours. And do I need one? I do if my vehicle is fuel injected and has Emission sensors! I do not if my vehicle is pre computer.
Fuel injected vehicles use a computer and sensors to maintain the correct air/fuel ratio. The main sensor is the oxygen sensor. Fuel injected vehicles have one or more oxygen sensors installed in the exhaust stream. The computer takes the information from the sensors and adjust the fuel flow accordingly. Because HHO causes the fuel to burns more efficiently.
We must make an adjustment and so we install the. Electronic Fuel Injection Enhancer (EFIE) The Effie tells the emissions computer that all is well. And this allows the engine run at peak.
Which EFIE do I need? If your engine is pre computer you need not use an EFIE. A Digital EFIE or a Wideband EFIE. Then we have a dual and quad version of each, and that just corresponds to the number of sensors that you have. Usually V6 and V8 engines need the quad version and 4 cylinder engines use the dual versions.
See below for more info on EFIEs. Do I need a PWM (Pulse width modulator)?The pulse width modulator (PWM) has an onboard trim potentiometer to control the amount of RMS voltage and current to your hydrogen booster. Your HHO Generator will run cooler and make more hydrogen which has greater ability to increase fuel mileage, however using Sodium Carbonate you can avoid using a PWM.
T is very simple, All our dry cells and kits have complete detailed installation instructions delivered with them. On average with the right tools and some mechanical know how it should not. Take longer than a few of hours.
What Maintenance do I do on my Hydrogen on Demand system? Make sure that the engine is off and the Generator is cool before servicing.
For extra safety, also remove the fuse to the battery connection before servicing. At the same time you will want to check all the hoses and electrical on your complete Hydrogen on Demand system for good connections. Check the water level about every gas fill up, keep it about 1"- 1 1/2" from the lid. These "HHO Generators", will produce Hydrogen and Oxygen. Hydrogen is a volatile colourless gas that has a low temperature ignition point.
This gas also has no smell. Serious injuries and bodily harm can occur if the device is not handled or used properly! NQ Hybrids takes no responsibility in damage to mechanical or bodily injury!
Please, Safety First when dealing with any hydrogen generators. This cell should not be operated without a bubbler or flash back device! Laboratory grade Sodium Carbonate as an electrolyte because they give equal results and keep the solution cleaner. It must be Laboratory grade as there are no contaminants in Lab grade chemicals.I use 50 to 100 gram/litre of distilled water. Once this has been mixed add to the reservoir, you should be able to see the water flowing into the dry cell. Bring the level up to the 3/4 mark on the reservoir and make sure to put the cap back on. Should be fully functioning and ready for a test drive. Before you take a test drive start the vehicle, you should now see the water in full circulation. Double check for air and water leaks at this time, use spray bottle and a teaspoon of dish soap once mixed spray on all of your hose connectors, bubbler cap and reservoir cap, if there are bubbles you have a leak and this needs to be fixed. Always read MSDS data sheets when using corrosive / caustic solutions. NQ Hybrids recommends a competent person installs there units. At peak efficiency you can expect this cell to produce suffient HHO at around 10 to 14 amps at 13.2 volts to give sustantial benefit to up to a 3000cc (3 litre) engine.
These HHO dry cells, and for that matter any Hydrogen on demand system added to a vehicle with a stock alternator, run at peak performance at under 18 amps. This is because at over 18 amps the alternator must work harder which in turn causes the engine to work harder, which uses more gas.If more HHO is needed, it is better to add more cells than increase the amperage, as this can often boil the cell which will produce steam and give a false indication of HHO output. The MAXIMUS 11 with its push in brass fittings makes adding additional cells a breeze! All our Version SS cells are pre-treated with anti foam agent so you always get off to a good start. All our cells are pressure tested and checked for Continuity. Once connected to the bubbler and vaporizer this Cell is ready to go just add electrolyte and power up!
FOR MORE INFORMATION message Us. If the question is not answered below, please give the size of engine in cc. Age, make and if diesel or petrol when requesting information.
With this HHO on demand System more of your primary fuel will be completely burned, smoothing out and improving overall operation. You will almost immediately notice a significant reduction in engine noise, as more complete combustion helps the engine to function correctly. For a about one month after HHO is installed the engine will continue to help remove built up carbon deposits which results from the unburnt fuel, This by itself will increase your economy and performance. The Plates Used in Our Dry Cells Are All Laser Cut and cross thatched.This does have an effect on performance and production of HHO gas!! The Acrylic end plates are 12mm thick rated at 145 degrees C. The inlet and outlet treads are1/4 The attachment bracket angles are aluminium 2 X 6mm SS wing nuts for easy connection to the power source. HHO will work on Diesel and Petrol and gas engines. Is a HHO dry cell system hard to install? It is very simple, all our dry cells and kits have complete detailed installation instructions delivered with them. What size cell do I need? As a rule an 11 plate will do up to a 3 litre engine a 21 plate up to 4.5 litre engine and for the bigger engines up to 6 litre the Brutus 11 plate truck cell. Do I need a PWM? To make the HHO production more efficient the use of a PWM /CCPWM is recommended as control over the amount of amps the cell draws is important and higher pulses increase HHO production. Do I need a EFFIE? Not all engines need an EEFIE.
It will depend greatly on the fuel type Diesel or petrol plus the year of manufacture. Please message for more info. Please state year and fuel type.
Australia We post via Australia Post. Generally, it takes 1-9 days to deliver parcel within Australia.5% of the value of the item. If the product is found to be defective, it will be replaced free of charge. We constantly monitor our inbox and will reply to your message within 24 hours. HHO generators designed by the leaders of HHO technology in Australia.
HHO manufactures use lower grades of Stainless steel like 304 and just run of the mill bolts and o rings. Here at NQ Hybrids, we only use high quality materials for our HHO generators and parts. NQ Hybrids strives to provide a high quality affordable HHO Generators and HHO Systems with the best possible customer service.
The item "AAA HHO HYDROGEN GEN MAXIMUS 11 PLATE SODIUM CARBONATE KIT EASY INSTALL V13" is in sale since Tuesday, October 16, 2012. This item is in the category "Vehicle Parts & Accessories\Car & Truck Parts\Air Intake, Fuel Delivery\Other".The seller is "stainless_steel_gates" and is located in Malanda, QLD. This item can be shipped worldwide.