HHO NEW MAXIMUS TURBO 21 PLATE BASIC KIT EASY INSTALL with KOH

  

Save the planet one step at a time. HHO NEW MAXIMUS TURBO 21 PLATE BASIC KIT EASY INSTALL with KOH. UP TO 4L ENGINE NO FUSS FITTINGS KOH ANTI FOAM. The AAA NEW MAXIMUS TURBO 21 Series is the easiest unit on the market to install. One touch 90 degree swivel fittings makes this unit a breeze to fit and you can add more cells quickly without fuss.

With bigger outlets and bigger bubbler the AAA MAXIMUS 21 produces more gas with less effort. Enough HHO for up to a 4.5 litre diesel or petrol engine and is able to have more cells added where needed. This unit has a bigger bubbler and 3/8 flow ports.

Bigger ports prevent choking of the cell and allows free flow of electrolyte thus more gas! Platinum Turbo 21Plate Dry Cell. All one touch HP tube fittings.

12 Self Tapping Mount Screws. Purpose built HHO 2.7 litre Bubbler tank. All electrical tabs and fittings needed.

(sufficent to make 6 litres). Please note: We do not include the wire. Suggested size 6mm auto wire for small 11 and 21 plate and 12mm for Brutus and twin cell systems. Wire size is relevant to distance from source and amp draw.

This unit does not include a PWM so the amperage must be controlled with electroliyte concentration. At peak efficiency you can expect this cell tp produce suffient HHO at around 10 to 14 amps at 13.2 volts to give sustantial benefit to up to a 4500cc (4.5litre) engine. These HHO dry cells, and for that matter any Hydrogen on demand system added to a vehicle with a stock alternator, run at peak performance at under 20 amps.

This is because at over 20 amps the alternator must work harder which in turn causes the engine to work harder, which uses more gas. If more HHO is needed, it is better to add more cells than increase the amperage, as this can often boil the cell which will produce steam and give a false indication of HHO output. With its one touch fittings makes adding additional cells a breeze.

This Cell is ready to go just add electrolyte and power up! IF the question is not answered below please when requsting information give size of engine in cc. Age, make and if diesel or petrol. Can I run my car totally on HHO? HHO is added to your engine and acts as a catalyst to ensure that a greater amount of fuel is burnt rather than thrown out the exhaust or wasted in generating heat and vibration. This in turn increases performance by smoothing out and improving overall operation. Almost immediately you will notice a significant reduction in engine noise, as a more complete combustion helps the engine to cycle correctly, this results in noticeable power increase. Over the next month or so the engine will remove built up carbon deposits from unburnt fuel, further increasing your performance & mileage and reducing your emissions. Fuel savings will depend greatly on the current inefficiency of your cars engine. Some older vehicles can get around 30 to 40% savings. What are your cells made of?

We use only 316L 18 gauge Stainless Steel in all our HHO Generators. The Plates Used in Our Dry Cells Are All Laser Cut, this does have an effect on performance and production of hho gas! The Acrylic end caps are 100mmX100mm X12mm thick rated at 145 degrees C.

The 2 hose barbs are 3/8 The attachment bracket angles are aluminium 2 X 6mm wing nuts for easy connection to the power source. What size cell do I need.

We recomend that you work on 1 litre of HHO per minute per 2500cc. Does it make a difference if it is a Petrol or Diesel Engine? HHO will work on both Diesel and Petrol engines. Customers with engines with intercoolers must do regular maintenance to clean out of the gas scrubber.

And do I need one? I do if my vehicle is fuel injected and has Emission sensors! I do not if my vehicle is pre computer. Fuel injected vehicles use a computer and sensors to maintain the correct air/fuel ratio.

The main sensor is the oxygen sensor. Fuel injected vehicles have one or more oxygen sensors installed in the exhaust stream. The computer takes the information from the sensors and adjust the fuel flow accordingly. Because HHO causes the fuel to burns more efficiently.

We must make an adjustment and so we install the. Electronic Fuel Injection Enhancer (EFIE) The Effie tells the emissions computer that all is well. And this allows the engine run at peak. Which EFIE do I need?

If your engine is pre computer you need not use an EFIE. A Digital EFIE is designed to cover most sensor types and is easy to install. Do I need a PWM (Pulse width modulator)? The pulse width modulator (PWM) has an onboard trim potentiometer to control the amount of RMS voltage and current to your hydrogen booster.

Your HHO Generator will run cooler and make more hydrogen which has greater ability to increase fuel mileage. Is a HHO dry cell system hard. T is very simple, All our dry cells and kits have complete detailed installation instructions delivered with them.

On average with the right tools and some mechanical know how it should not. Take longer than a few of hours. What Maintenance do I do on my Hydrogen on Demand system? Make sure that the engine is off and the Generator is cool before servicing. For extra safety, also remove the fuse to the battery connection before servicing.

At the same time you will want to check all the hoses and electrical on your complete Hydrogen on Demand system for good connections. Check the water level about every gas fill up, keep it about 1"- 1 1/2" from the lid.

These "HHO Generators", will produce Hydrogen and Oxygen. Hydrogen is a volatile colourless gas that has a low temperature ignition point. This gas also has no smell. Serious injuries and bodily harm can occur if the device is not handled or used properly! NQ Hybrids takes no responsibility in damage to mechanical or bodily injury!

Please, Safety First when dealing with any hydrogen generators. This cell should not be operated without a bubbler or flash back device!

Now the installation of your unit should be complete. You are now going to Mix the Catalyst (electrolyte) with Distilled Water. Potassium Hydroxide is the best electrolyte for a Hydrogen Generator. We wont use any thing else for catalyst in our HHO Dry cells. The strength of your electrolyte mixture is what controls the amps drawn by your dry cell.

To keep my unit running at 18 Amps or less and get a least 1 liter per minute of gas or more Start with 100gms of KOH to 900 gms of. Distilled water for start up , you may need to add more to get higher amps but run your unit with a weak solution to condition it first. Use "Safety First" rules when mixing KOH or other caustic materials.

Mix thoroughly in a separate container. Once this has been mixed add to the reservoir, you should be able to see the water flowing into the dry cell. Bring the level up to the 3/4 mark on the reservoir and make sure to put the cap back on. Should be fully functioning and ready for a test drive. Before you take a test drive start the vehicle, you should now see the water in full circulation.

Double check for air and water leaks at this time, use spray bottle and a teaspoon of dish soap once mixed spray on all of your hose connectors, bubbler cap and reservoir cap, if there are bubbles you have a leak and this needs to be fixed. Is to use Laboratory grade Sodium Carbonate or Sodium Hydroxide as an electrolyte because they give equal results and keep the solution cleaner. It must be Laboratory grade as there are no contaminants in Lab grade chemicals. I use 90 gram/litre of distilled or demineralized water. Sodium Hydroxide 97%pure, at 10 gram/litre of distilled or demineralized water. Posting within Australia: We post via Australia Post. Generally, it takes 1-9 days to deliver parcel within Australia.

Some countries do not offer the availability of. VISIT OUR STORE FOR MORE HHO OPTIONS. Always read MSDS data sheets when using corrosive / caustic solutions.

NQ Hybrids recommends a competent person installs there units. All our Version SS cells are pre-treated with anti foam agent so you always get off to a good start. All our cells are pressure tested and checked for Continuity. Once connected to the bubbler and vaporizer this Cell is ready to go just add electrolyte and power up! FOR MORE INFORMATION message Us.

If the question is not answered below, please give the size of engine in cc. Age, make and if diesel or petrol when requesting information. With this HHO on demand System more of your primary fuel will be completely burned, smoothing out and improving overall operation. You will almost immediately notice a significant reduction in engine noise, as more complete combustion helps the engine to function correctly. For a about one month after HHO is installed the engine will continue to help remove built up carbon deposits which results from the unburnt fuel, This by itself will increase your economy and performance. The Plates Used in Our Dry Cells Are All Laser Cut and cross thatched.

This does have an effect on performance and production of HHO gas!! The Acrylic end plates are 12mm thick rated at 145 degrees C. The inlet and outlet treads are1/4 The attachment bracket angles are aluminium 2 X 6mm SS wing nuts for easy connection to the power source.

HHO will work on Diesel and Petrol and gas engines. Is a HHO dry cell system hard to install? It is very simple, all our dry cells and kits have complete detailed installation instructions delivered with them.

On average with the right tools and some mechanical know how it should not take longer than a few of hours. What size cell do I need? As a rule an 11 plate will do up to a 3 litre engine a 21 plate up to 4.5 litre engine and for the bigger engines up to 6 litre the Brutus 11 plate truck cell.

Do I need a PWM? To make the HHO production more efficient the use of a PWM /CCPWM is recommended as control over the amount of amps the cell draws is important and higher pulses increase HHO production. Do I need a EFFIE? Not all engines need an EEFIE. It will depend greatly on the fuel type Diesel or petrol plus the year of manufacture. Please message for more info. Please state year and fuel type. Australia We post via Australia Post. 5% of the value of the item. If the product is found to be defective, it will be replaced free of charge. We constantly monitor our inbox and will reply to your message within 24 hours.

HHO generators designed by the leaders of HHO technology in Australia. HHO manufactures use lower grades of Stainless steel like 304 and just run of the mill bolts and o rings.

Here at NQ Hybrids, we only use high quality materials for our HHO generators and parts. NQ Hybrids strives to provide a high quality affordable HHO Generators and HHO Systems with the best possible customer service. The item "HHO NEW MAXIMUS TURBO 21 PLATE BASIC KIT EASY INSTALL with KOH" is in sale since Sunday, June 19, 2016. This item is in the category "Vehicle Parts & Accessories\Car & Truck Parts\Air Intake, Fuel Delivery\Other".

The seller is "stainless_steel_gates" and is located in Malanda, QLD. This item can be shipped worldwide.

• Compatible Makes: ALL MAKES
• HHO GENERATOR: SAVE FUEL
• POWER BOOSTER: HYDROGEN BOOSTER
• Brand: NQHYBRIDS
• Manufacturer Part Number: NQ21B